Still1 Build Thread
Posted: November 7th, 2014
Hello Everyone,
Welcome to my build thread! Hope you guys enjoy.
BBP 2008 Accord Coupe V6 Auto
Engine
Takeda SRI1
Milled MDX riser and 2 P2R thermal gaskets
UR Underdrive pulley
KTuner
Wheels
Concept Ones "Raven" F-20X8.5 R-20X9.5 offset +25
K3 Projekt 1 F-20x9 +20 R-20x11 +18 (Current)
Exterior
HFP Front lip and Sidekirts
m3 style roof spoiler
Side moldings
20% tint
Plasti dip rear bumper
Plasti dip grille
Weathertech Window visors
Lights
Nokya Hyper Yellow Fogs
VMME 5000k HIDs
Exhaust
ATLP Jpipe
Magnaflow mufflers
Magnaflow 3" quad tips
Magnaflow Catback (Current)
Megan Test pipe
Suspension
FF type 1
Dropped on FF type 1s and Weathertech visors installed
XXR 527s 18x8.75 +35 square with stock tires
20% tint
Fogs and HIDs installed
M3 style roof spoiler installed
Plasti Dipped lower rear bumper
Magnaflow Mufflers and Quad tips installed
Concept Ones installed (Ty CoolBlue for the purchase :])
HFP Side Skirts installed
HFP Front Lip installed
Front Lip color was mismatched so I had to get it redone, not perfect, but a lot better! Before and After
Some shots after the front lip was painted
Prepping my roof for vinyl install! First time washing my car (sorta) in the rain...gotta love the PNW
Laying down the vinyl after the prep
One side done
Finally done! Not the cleanest job, but happy with the way it turn out. Definitely harder than the youtube videos made it look lol
ATLP jpipe Installed, install went pretty smooth. Got a megan test pipe that still needs to be installed!
Definitely sounds a little deeper and pulls a little harder mid range.
Raised the whip an inch all around and switched back to stocks. While I had the car up I installed my megan test pipe.
Got my MDX riser installed, along with two P2R thermal gaskets. Got a CEL at the beginning, but took everything apart and applied some gasket sealant, which fixed the problem.
Install was pretty easy, however, I dropped one of the bolts and it fell under the intake runners which was a biatch to get.
New shoes
enjoying them before I gotta switch back to "winter" mode...Hopefully going to install my UR underdrive pulley (finally), get my exhaust redone, possibly get tb and intake manifold, vcm delete, hfp rear lip, then tune.
Plasti dipped the outer part of the grille
Got my UR pulley installed FINALLY.
Welcome to my build thread! Hope you guys enjoy.
BBP 2008 Accord Coupe V6 Auto
Engine
Takeda SRI1
Milled MDX riser and 2 P2R thermal gaskets
UR Underdrive pulley
KTuner
Wheels
Concept Ones "Raven" F-20X8.5 R-20X9.5 offset +25
K3 Projekt 1 F-20x9 +20 R-20x11 +18 (Current)
Exterior
HFP Front lip and Sidekirts
m3 style roof spoiler
Side moldings
20% tint
Plasti dip rear bumper
Plasti dip grille
Weathertech Window visors
Lights
Nokya Hyper Yellow Fogs
VMME 5000k HIDs
Exhaust
ATLP Jpipe
Magnaflow mufflers
Magnaflow 3" quad tips
Magnaflow Catback (Current)
Megan Test pipe
Suspension
FF type 1
Dropped on FF type 1s and Weathertech visors installed
XXR 527s 18x8.75 +35 square with stock tires
20% tint
Fogs and HIDs installed
M3 style roof spoiler installed
Plasti Dipped lower rear bumper
Magnaflow Mufflers and Quad tips installed
Concept Ones installed (Ty CoolBlue for the purchase :])
HFP Side Skirts installed
HFP Front Lip installed
Front Lip color was mismatched so I had to get it redone, not perfect, but a lot better! Before and After
Some shots after the front lip was painted
Prepping my roof for vinyl install! First time washing my car (sorta) in the rain...gotta love the PNW
Laying down the vinyl after the prep
One side done
Finally done! Not the cleanest job, but happy with the way it turn out. Definitely harder than the youtube videos made it look lol
ATLP jpipe Installed, install went pretty smooth. Got a megan test pipe that still needs to be installed!
Definitely sounds a little deeper and pulls a little harder mid range.
Raised the whip an inch all around and switched back to stocks. While I had the car up I installed my megan test pipe.
Got my MDX riser installed, along with two P2R thermal gaskets. Got a CEL at the beginning, but took everything apart and applied some gasket sealant, which fixed the problem.
Install was pretty easy, however, I dropped one of the bolts and it fell under the intake runners which was a biatch to get.
New shoes
enjoying them before I gotta switch back to "winter" mode...Hopefully going to install my UR underdrive pulley (finally), get my exhaust redone, possibly get tb and intake manifold, vcm delete, hfp rear lip, then tune.Plasti dipped the outer part of the grille
Got my UR pulley installed FINALLY.